- #Wiring and parts for a 1994 wolffe sunquest tanning bed install#
- #Wiring and parts for a 1994 wolffe sunquest tanning bed skin#
NOTE:Save the red jumper wire and tape to back of bed for future use.
#Wiring and parts for a 1994 wolffe sunquest tanning bed install#
T-Max remove the red jumper wire from the removable section of the plug.ī) Install new timer wires where the red jumper was located. If you are not using a remote be sure that the plugs are attached to each other.Ī) When using a remote timer other than a Remote time port is located at the rear of the bed across from the timer. DO NOT ATTEMPT TO PLUG ANY OTHER DEVICES INTO THESE RECEPTACLES.Ħ. Plug the body fan into the receptacle located beneath the bed. Attach the body fan at either end of the bench using the screws provided. Canopy should stay in the open position.ĥ. Slowly raise canopy, remove 2 x 4's and attach the large end of the piston to the top ball stud. Install the 3/8" bolt though the shoulder washer and bushing. Align the top hole of the hinge with the hole in the canopy. Make sure you line up the rails or the styrofoam will break. Place the canopy CAREFULLYon the Styrofoam or 2x4's that you placed on the bench. Remove the 3/8" x 1.5" bolts from the ends. Nylon washers go between the hinge and the bed end cap.ģ.Remove canopy from the box. Remove the 3/8" x 1" bolts from the ends of the lounge. CAUTION: DO NOT REMOVE FOAM PROTECTING THE TIMER, AS THE BUTTONS MAY TEAR WHEN TURNING THE BED OVER.Ģ. Turn bench over so it is standing on the legs. Side skirt installs behind front skirt with the 8 screws provided (you should be able to see into the slotted louvres). Attach the pistons to the ball stud at each end (the smaller shaft is attached to the bench).ġC.Attach front skirt and side skirt. Remove the eight 5/16" x 1 " bolts from the bench panel.ġB.Remove the 42" x 16" pieces of styrofoam from the box and place them across the bench rails (or use 2x4's). Place lounge, bulbs facing down, on a soft surface. General Overview w/ Ballasts & CapacitorsĬlick here for a picture of electrical outlet placementĬlick here for a picture of ideal in-room bed placementġA.Remove lounge from box. As always, please call with any questions ph.
![wiring and parts for a 1994 wolffe sunquest tanning bed wiring and parts for a 1994 wolffe sunquest tanning bed](https://f01.justanswer.com/slowboy57/2014-05-26_151211_sunvision_g-24sh_004_small.jpg)
![wiring and parts for a 1994 wolffe sunquest tanning bed wiring and parts for a 1994 wolffe sunquest tanning bed](https://i.ytimg.com/vi/VBecb_l6_1Y/hqdefault.jpg)
![wiring and parts for a 1994 wolffe sunquest tanning bed wiring and parts for a 1994 wolffe sunquest tanning bed](https://i.ebayimg.com/thumbs/images/g/E8MAAOSwgGphkP3W/s-l300.jpg)
In this instance these pictures can be invaluable in locating the correct part. We recognize that you are new to the tanning industry and might not know what all the components look like in a tanning bed. In many cases the replacement parts are small and easily accessible and can be replaced by you or your staff. Occasionally your tanning bed may need to be repaired or parts replaced. And together with the 400 watt HP bulbs ensures your whole body tanning experience is synergistic and unrivaled.This page was designed to assist you in repairing your tanning bed. The Elite 'SELECT' 20M lamps equal the original Velocity or Diamond Sun S lamps in output and soft bronzing ability intended for this application. The factory original lamp/bulb combination is hard to beat in the way the components work in conjunction with each other. This is perfect for our faces as we spend time outdoors making it harder to achieve a bronze color without reddening. Underneath the blue glass UV filters reside high potency (high pressure) bulbs which emit high amounts of UVA the bronzing rays.
![wiring and parts for a 1994 wolffe sunquest tanning bed wiring and parts for a 1994 wolffe sunquest tanning bed](https://i.ytimg.com/vi/RFaIRUHhN2Y/hqdefault.jpg)
#Wiring and parts for a 1994 wolffe sunquest tanning bed skin#
Why three choices.Will these all work in my bed? They vary in strength to match your skin and tanning preferences. Learn about your options by seeing what we recommend. These Wolff Elite tanning bulbs will work in any tanning bed that uses 100 watt bulbs, and were designed specifically for your 28 2F Sunquest or Sunvision 28 Le2F tanning unit equipped with a 20 MINUTE TIMER.